基本信息
浏览量:1
职业迁徙
个人简介
New Proton-Exchange Membranes for Fuel Cells
Composite Nanofiber Network Membranes:
We are developing a completely new approach to ion-exchange membrane preparation, where a three-dimensional interconnected network of electrospun polyelectrolyte nanofibers is created and then the interfiber voids are filled with an inert/uncharged polymer. Such a phase-separated nanomorphology is not unlike the desired/ideal structure in a block copolymer system, but there is more flexibility in the fabrication approach. Thus, the polyelectrolyte, fiber diameter, fiber volume fraction, and inert polymer can be chosen/fixed independently. The uncharged (hydrophobic) polymer which surrounds each nanofiber restricts fiber swelling in water and provides mechanical strength to the membrane, thus permitting the fibers to have a fixed-charge concentration much greater than that which is practical in a homogenous ion-exchange membrane. Also, the interconnecting nanofiber structure ensures optimum utilization of percolation pathways of the ionomer.
Pre-Stretched Recast Nafion®:
A new Nafion membrane micromorphology has been generated by uniaxially stretching and then annealing a gelled (10% solvent content)cast film. The proton conductivity of uniaxially pre-stretched recast Nafion (0.1 S/cm at 25oC for membranes in water) was independent of draw ratio, whereas the methanol permeability decreased by a factor of 1.4-2.0, as compared to commercial Nafion, for films elongated to a draw ratio of 4. A pre-stretched recast Nafion film in the 130-180 μm thickness range, when used in a direct methanol fuel cell, generated a high power density at 0.4 V (88 mW/cm2 at 60oC, 1.0 M methanol, and ambient pressure air), as compared to 58 mW/cm2 for Nafion 117. Very high power was generated with pre-stretched recast Nafion (180 μm) by increasing the cell temperature to 80oC, increasing the anode/cathode catalyst loading to 8.0 mg/cm2, and increasing the cathode air pressure to 25 psig. Under these conditions the power density at 0.4 V for a 1.0 M methanol feed solution was 240 mW/cm2 and the maximum power density was 252 mW/cm2 (at 0.35 V).
Alkaline Fuel Cell Membranes:
Our approach is to fabricate a phase-separated segmented copolymer anion-exchange membrane with hydrophobic (non-polar) blocks to limit membrane swelling and impart mechanical strength to the membrane and hydrophilic (polyelectrolyte) blocks with backbone dimethyl ammonium anion-exchange groups for OH- conduction. We are targeting membranes with the following properties: (i) a hydroxyl ion conductivity of between 0.08 and 0.15 S/cm for a water-equilibrated membrane at 25oC, (ii) a water swelling at 25oC of 25-75%, (iii) a thickness of 50 μm, and (iv) good mechanical properties when immersed in water or an aqueous methanol solution.
Polyphosphazene-Based Membranes:
Polyphosphazenes, a class of hybrid organic/inorganic polymers, are being investigated for use as the membrane material in direct liquid methanol and hydrogen/air PEM (proton exchange membrane) fuel cells. Selected polyphosphazenes are sulfonated, crosslinked and/or blended with an inert polymer, cast into thin films, characterized, and then tested in a fuel cell. Work in this area includes fundamental polymer chemistry (sulfonation of polymers, polymer blending, and solid-state crosslinking), membrane characterization (measurement of solvent permeability, proton conductivity, solvent swelling, and mechanical/thermal properties), and fuel cell evaluation (preparation of membrane-electrode-assemblies and fuel cell performance testing).
Development of Space-Charge Models for Ion Uptake and Transport in Ion-Exchange Membranes
Theories for multicomponent ion uptake and transport are being developed and tested. The models consider solvation free energy changes that occur during ion sorption, the orientation of solvent dipoles inside a membrane pore (due to the strong electric field generated by the membrane's fixed charge groups), and ion-pair formation between multivalent counterions and membrane fixed-charge sites. Models have been applied to sorption and transport of monovalent and monovalent/divalent cation salt mixtures in Nafion® cation-exchange membranes and in commercial anion-exchange membranes. Future work is focused on weak electrolyte uptake in cation-exchange membranes, membrane transport with non-aqueous and mixed solvents, and amino acid uptake and transport in ion-exchange membranes.
Organic Electrochemical Synthesis
Organic electrochemical reactions are being carried out in PEM (proton-exchange membrane) fuel cell reactors that do not require a supporting electrolyte salt and can accommodate gaseous feed streams. Fuel cell reactors are currently being investigated for organic electro-hydrogenation reactions, using precious metal catalyst powder electrodes with either water or H2 gas as the source of hydrogen. In one project, edible oils (e.g., soybean and canola oils) have been partially hydrogenated electrochemically in a PEM reactor. Partially hydrogenated oil products were characterized by a low percentage of trans fatty acid isomers (which are known contributors to coronary heart disease) and a moderately/sufficiently high concentration of saturated stearic acid for different food applications.
研究兴趣
论文共 272 篇作者统计合作学者相似作者
按年份排序按引用量排序主题筛选期刊级别筛选合作者筛选合作机构筛选
时间
引用量
主题
期刊级别
合作者
合作机构
John B. Waugh,Siddharth Komini Babu,Qinjun Kang,Nicole K. Moehring, Angelica Benavidez, Xiaojing Wang,Piran R. Kidambi,Peter N. Pintauro,Jacob S. Spendelow
Desalinationpp.117610, (2024)
crossref(2024)
JOURNAL OF POWER SOURCES (2023): 233679-233679
BATTERIES-BASELno. 12 (2023)
ECS Meeting Abstractsno. 44 (2022): 1661-1661
引用0浏览0引用
0
0
ECS Meeting Abstractsno. 38 (2022): 1710-1710
加载更多
作者统计
合作学者
合作机构
D-Core
- 合作者
- 学生
- 导师
数据免责声明
页面数据均来自互联网公开来源、合作出版商和通过AI技术自动分析结果,我们不对页面数据的有效性、准确性、正确性、可靠性、完整性和及时性做出任何承诺和保证。若有疑问,可以通过电子邮件方式联系我们:report@aminer.cn